BRYSTON 4B SST MANUAL PDF

BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Akinotaxe Gardagar
Country: Liechtenstein
Language: English (Spanish)
Genre: Photos
Published (Last): 2 September 2015
Pages: 166
PDF File Size: 1.24 Mb
ePub File Size: 13.87 Mb
ISBN: 922-1-84400-755-8
Downloads: 98095
Price: Free* [*Free Regsitration Required]
Uploader: Sara

The single ended or unbalanced input is provided for pre-amps without balanced output. The Output binding posts provide three different interconnect options. Bridged W 8 ohms Max. See figure 2 below. Do not over tighten or the binding post may become damaged. Use quality wire, and if runs are more than 3 meters use at least 12 gage wire.

Bryston C Series 4B SST Dimensional Drawing

Lugs should be gold plated. Connect to this post the – terminal on the loudspeaker. Tampering by persons other than factory authorized service personnel, or mznual to fully comply with Bryston operating instructions, voids the warranty.

Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink.

Bryston 4B SST User’s Manual |

This warranty gives you specific legal rights and you may also have other rights which may vary from province to province and country to country. Never operate the amplifier in a vertical position.

  AVE VERA VIRGINITAS PDF

Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application. Master circuit – breaker. Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical.

Bryston 4BSST User Manual

The most important installation consideration is ventilation. The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. The amplifier will now power-up only when the control voltage is present on.

Bryston 4BSST User Manual | 8 pages | Also for: 3BSST

This warranty is considered void if the defect, malfunction or failure of the product or any component part was caused by damage not resulting from a defect or malfunction or abuse while in the possession of the customer. Also see installation section on ventilation.

Unrestricted air-flow across its heat sinks is a must. Gold plated spade lugs are available from Bryston. Different input configurations result in slightly different noise readings. The above noise ratings represent minimum readings, actual readings may be better. The speaker binding posts will accept wire up to 3 gage in size.

Spade lugs provide high contact area and secure fastening. On the rear panel is provided a high current plug for the power cord receptacle.

In the event of a defect brysfon malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance. Any SST channels thermally shutting down during operation indicates insufficient air flow, and a remedy must be found for 4 the amplifier. Input Sensitivity Gain Switch. This includes parts, labour and return shipping to the first owner and all subsequent owners. Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the post knob.

  DICCIONARIO DE ESPIRITUALIDAD IGNACIANA PDF

If both channel LED indicators are unlit the amplifier probably needs only to be powered on.

Graph shows that distortion is essentially unaffected by load. Should your instillation conditions be constricted, then additional forced air-cooling may be necessary.

When the power supplies have stabilized the channel will come out of mute and the LED will change to green normal operation. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston. Balanced systems provide noise rejection from external electrical interference, so cable length can be very long 50m or longer.

Gold plated locking banana plugs are available from Bryston. This is the home theatre setting for balanced operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less. This will ensure the amplifier is protected in future transport.